Data Sheets

Aluminium Alloy - Commercial Alloy - 3003 '0' Sheet

3003 '0' Sheet

Aluminium alloy 3003 is a medium strength alloy with very good resistance to atmospheric corrosion and very good weldability as well as good cold formability. It has better mechanical properties, especially at elevated temperatures than the 1000 series alloys.

Applications - Alloy 3003 is typically used for:
Building industry: roofing and sidings, acoustic ceilings, corrugated sheets
Chemical and food industries: storage tanks, pipes, metal work
Equipment for heating and cooling: heat exchangers, air condition evaporators, motor vehicle radiators, freezer linings
Home appliances: cooking utensils, bakery moulds
Office equipment
Tube & Pipe
Packaging: containers, closures. Cladding alloy.


Chemical Composition

Spec: BS EN 573-3:2009

Alloy 3003

Chemical Element % Present
Others (Total) 0.0 - 0.15
Cobalt (Co) 0.05 - 0.20
Hydrogen (H) 0.0 - 0.70
Magnesium (Mg) 1.00 - 1.50
Silicon + Iron (Si+Fe) 0.0 - 0.60
Zirconium (Zr) 0.0 - 0.10
Other (Each) 0.0 - 0.05
Aluminium (Al) Balance

Properties

Physical PropertyValue
Density 2.73 g/cm³
Melting Point 655 °C
Thermal Expansion 23.1 x10^-6 /K
Modulus of Elasticity 69.5 GPa
Thermal Conductivity 190 W/m.K
Electrical Resistivity 0.034 x10^-6 Ω .m

Spec: BS EN 485-2:2008

Sheet - 0.2mm to 6.00mm

Mechanical PropertyValue
Tensile Strength 95 - 135 MPa
Proof Stress 35 Min MPa
Hardness Brinell 28 HB

Alloy Designations

Aluminium alloy 3003 also corresponds to the following standard designations and specifications:

 

 


Temper Types

The most common tempers for 3003 aluminium are:

  • O - Soft

Supplied Forms

Alloy 3003-0 is normally supplied as soft sheet

  • Sheet

Weldability

Alloy 3003 has very good weldability


Fabrication

Workability – Cold: Very Good

Machinability: Acceptable

Weldability – Gas: Very Good

Weldability – Arc: Very Good

Weldability – Resistance: Good

Brazability: Very Good

Solderability: Very Good

Download PDF Version

Datasheet Search

Last Datasheet Revision

8 January 2016

Disclaimer

This Data is indicative only and as such is not to be relied upon in place of the full specification. In particular, mechanical property requirements vary widely with temper, product and product dimensions. All information is based on our present knowledge and is given in good faith. No liability will be accepted by the Company in respect of any action taken by any third party in reliance thereon.

Please note that the 'Datasheet Update' date shown above is no guarantee of accuracy or whether the datasheet is up to date.

The information provided in this datasheet has been drawn from various recognised sources, including EN Standards, recognised industry references (printed & online) and manufacturers’ data. No guarantee is given that the information is from the latest issue of those sources or about the accuracy of those sources.

Material supplied by the Company may vary significantly from this data, but will conform to all relevant and applicable standards.

As the products detailed may be used for a wide variety of purposes and as the Company has no control over their use; the Company specifically excludes all conditions or warranties expressed or implied by statute or otherwise as to dimensions, properties and/or fitness for any particular purpose, whether expressed or implied.

Advice given by the Company to any third party is given for that party’s assistance only and without liability on the part of the Company. All transactions are subject to the Company’s current Conditions of Sale. The extent of the Company’s liabilities to any customer is clearly set out in those Conditions; a copy of which is available on request.