Downloads

All Metals - REACH - REACH - Aluminium

REACH - Aluminium

EC Regulation 1907/2006 Concerning the Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH).
REACH Enforcement Regulations 2008

The regulations require all ‘substances’, which includes all metals, to be registered under REACH. It is important, however, to note that REACH Regulations distinguish between ‘substances’ and ‘preparations’ (which are covered by REACH) and ‘articles’ (which are not governed by REACH and do not require registration).

The Company’s standard semi-finished products in aluminium, aluminium alloys, stainless steel and copper alloys such as sheet, plate, tube, bar and extrusions, are all classed as ‘articles’ and do not need to be registered. Billets, blooms, concast slabs and machined ingots are all also classed as ‘articles’ and do not need to be registered. However, certain types of ingots such as ‘as cast’ ingots, rolling ingots and ingots produced for extrusion processes, are classed as ‘preparations’ and would, therefore, need to be registered.

For the reasons stated, The Company can confirm that products supplied to you from its standard range are classified as ‘articles’ and therefore do not need to be registered under REACH.

A copy of the production diagrams for aluminium and stainless steel is available on request, to help clarify the definitions of ‘substances’, ‘preparations’ and ‘articles’.

Due diligence has been carried out on The Company’s current supplier base to establish that ‘substances’ and ‘preparations’ which require registration under REACH have been registered or confirm the absence of such chemicals. For this reason, as far as reasonably practicable, The Company can confirm that the majority of its standard semi-finished products detailed above, do not contain any of the chemicals listed in the current Candidate List of Substances of Very High Concern (SVHC) July 2018.

The only exception to compliance is where a grade of material is ordered by a customer where the British, European or International Standard covering the grade requires a deliberate addition of one or more of the substances in order to comply with the standard/grade requirements. In this case, the material will contain a value of each substance in line with the standard requirements.

It is possible that you may purchase other products or metal types from The Company that are outside of its normal stock range. In these circumstances, The Company would need to check with the producer that these specific products do not contain any of the listed Substances of Very High Concern and advise you accordingly.

The Company trusts that this information clarifies its position regarding compliance with the REACH Regulations. If you have any questions or want to check on any specific product that you are unsure about, please contact The Company.

This Policy will be updated on amendments to the legislation and as a minimum annually.

METAL PROCESSING - SHOWN FOR ALUMINIUM PRODUCTS AS EXAMPLE
The example of aluminium processing is included to show the transition point in the processing of bauxite to final aluminium products. It should be noted that the processing of other metals (for example iron / steel) may show different transition points. The following figure shows the different processing stages and the respective status of the raw material.


Illustrative example of the general transition point from mineral to final aluminium article.

The transition point from preparation to article is set between rolling ingots and sheets, extrusion ingots and extrusion profiles and aluminium alloy and alloy cast pieces.

Similar raw material type in the form of metal and alloy semi-finished products as coil and profile are: bars, blanks (e.g. cut, machined, pressed, etc), coil (coated and uncoated), extrusion profiles, films and filaments, foil and ribbons, forgings, plate, pipe and tube (cast, seamless and welded), pipe and tube fittings, sintered semi-finished and final products, sheet and strip (coated and uncoated), stampings, wire rod and wire (coated and uncoated).

Download PDF Version

Datasheet Search

Last Datasheet Revision

12 July 2018

Disclaimer

This Data is indicative only and as such is not to be relied upon in place of the full specification. In particular, mechanical property requirements vary widely with temper, product and product dimensions. All information is based on our present knowledge and is given in good faith. No liability will be accepted by the Company in respect of any action taken by any third party in reliance thereon.

Please note that the 'Datasheet Update' date shown above is no guarantee of accuracy or whether the datasheet is up to date.

The information provided in this datasheet has been drawn from various recognised sources, including EN Standards, recognised industry references (printed & online) and manufacturers’ data. No guarantee is given that the information is from the latest issue of those sources or about the accuracy of those sources.

Material supplied by the Company may vary significantly from this data, but will conform to all relevant and applicable standards.

As the products detailed may be used for a wide variety of purposes and as the Company has no control over their use; the Company specifically excludes all conditions or warranties expressed or implied by statute or otherwise as to dimensions, properties and/or fitness for any particular purpose, whether expressed or implied.

Advice given by the Company to any third party is given for that party’s assistance only and without liability on the part of the Company. All transactions are subject to the Company’s current Conditions of Sale. The extent of the Company’s liabilities to any customer is clearly set out in those Conditions; a copy of which is available on request.